BFG3-50 High Pressure Diaphragm Pump
BFG3-50 High Pressure Diaphragm Pump
| Model: BFG3-50 Max. Flow: 568L/min Max.Suction Height: 5m Max.Outlet Pressure: 1.4Mpa |
| Inlet/outlet size: 2'' Flange Air Inlet Size: 1/2'' Max. Particle Size: 6.4mm Air Comsumption: 1.5-2.0m3/min |
| Air Source Pressure: 0.7Mpa Voltage: 220V Power: 50W |
Buy Online
Introduction
| What if the air source pressure is too small? | |
| What if the filter press mud cake can not be pressed dry? | |
| What if the filter press working time is too long? | |
| · Complete Function · Easy Installation · Intelligent Control · High Efficiency High Pressure Diaphragm Pump for your one-stop solution to the above problems! |
|
| High Pressure Diaphragm Pump | Ordinary Pneumatic Diaphragm Pump |
 |
 |
| The outlet pressure is up to 14 kg, and the head can reach 140 meters. | The maximum outlet pressure is only 8 kg, and the head is 80 meters. |
| Mud cake has high compression rate and low water content of 42%. | The mud cake compression rate is low,water content is 80%-85%. |
| Short time consuming. lt only takes1-2 hours to complete the high-pressure phase. | It takes a long time, 5-8 hours in the high-pressure phase. |
|
|
BFG3 Series High Pressure Diaphragm Pump is a special equipment mainly used for filter press feeding in sewage treatment, the flow range is between 378.5~1041L/min, and the highest working pressure is 1.4MPa. |
|
| Product Advantages of High Pressure Diaphragm Pump | |
| Transportation costs are cut in half The compression ratio is high and the volume is smaller. Originally, 2 cars needed to be loaded, but now only 1 car is loaded. |
Intelligent switching is more efficient High and low pressure automatic switch completely without manual operation. |
| Cleaner discharge The original pressure filtration is not dry, muddy water is turbid, now the super pressure filtration separation is more thorough. |
Work consumes less air Equivalent to a single diaphragm pump air consumption. |
| Dry, use less electricity The original water content is 80% and the current water content is 42%. |
Work takes less time It used to take 20 hours, but now it takes 5 hours. |
| Work Process of High Pressure Diaphragm Pump | |
|
|
When High Pressure Diaphragm Pump starts, first the filter press is provided with low pressure and high flow rate liquid material to fill the filter chamber quickly. |
|
|
As the filtration process goes on, the thickness of the filter cake gradually increases and the filtration resistance increases. |
|
|
When the outlet pressure is greater than the set value, the system automatically switches to the high pressure state and continues to deliver high pressure material liquid to the filter press. |
|
|
Until the filter cake inside the plate frame reaches the rated thickness and the pressing effect of the filter press reaches the best state. |
Specification Parameters
| Model | Max. Flow （L/min） |
Max.Suction Height（m） | Max.Outlet Pressure (Mpa) | Inlet/outlet size(in) |
Max. Particle Size(mm) | Air Comsumption (m3/min) |
Air Source Pressure (Mpa) | Voltage (V) |
Power (W) |
Air Inlet Size(in) |
| BFG3-40 | 378.5 | 5 | 1.4 | 1-1/2'' | 4.8 | 0.9 | 0.7 | 220 | 50 | 1/2'' |
| BFG3-50 | 568 | 5 | 1.4 | 2'' | 6.4 | 1.5-2.0 | 0.7 | 220 | 50 | 1/2'' |
| BFG3-80 | 1041 | 5 | 1.4 | 3'' | 9.4 | 3.0-4.0 | 0.7 | 220 | 50 | 3/4'' |
